Difference between revisions of "Example-NSF-14 1.9"

Latest revision as of 10:59, 10 February 2009

Authors:
Fermín Galán (galan at dit.upm.es)
Francisco José Martín Moreno (fjmartin at dit.upm.es)
Miguel Ferrer Cámara (mferrer at dit.upm.es)
version 1.9, January 29st, 2009

Scenario

NFS (National Science Foundation) is the US Research and Education Network (NREN). Although there are several incarnations of the NFS net, here we consider the one described in the following document (also shown in the figure below) is composed of 14 network nodes connected through 21 point-to-point links (each one a /30 network).

Figure 1: NSFNet topology (with 14 nodes)

A VNUML scenario implementing the NSF topology is shown in this example. All the routers in the simulation run ospfd, a daemon process from the Zebra Suite that implements OSPF protocol. This protocol allows each router to configure dynamic routes so, after a convergence time, global connectivity is achive once the simulation has been started. Since version 1.9 of VNUML, OSPF-based routing have been implemented using OSPFD plugin with this configuration file.

Once the scenario is up, start the routing daemons (which configuration files are automatically generated by the OSPF plugin) using the following command:

vnumlparser.pl -x start@nsf-14.xml -v

Some examples of test performed with this virtual scenario:

Connectivity from WA to GA:

root@WA:~# traceroute 10.0.50.13
traceroute to 10.0.50.13 (10.0.50.13), 30 hops max, 38 byte packets
 1  10.0.5.6 (10.0.5.6)  0.371 ms  0.579 ms  0.262 ms
 2  10.0.5.22 (10.0.5.22)  0.472 ms  0.420 ms  0.426 ms
 3  10.0.50.13 (10.0.50.13)  0.594 ms  0.586 ms  0.507 ms

Connectivity from WA to NJ:

traceroute to 10.0.50.11 (10.0.50.11), 30 hops max, 38 byte packets
 1  10.0.5.10 (10.0.5.10)  2.862 ms  0.279 ms  0.226 ms
 2  10.0.5.46 (10.0.5.46)  0.421 ms  2.355 ms  0.414 ms
 3  10.0.50.11 (10.0.50.11)  0.561 ms  0.476 ms  1.424 ms

OSPF information from ospfd at WA:

WA# sh ip ospf route
============ OSPF network routing table ============
N    10.0.5.0/30           [10] area: 0.0.0.0
                           directly attached to eth1
N    10.0.5.4/30           [10] area: 0.0.0.0
                           directly attached to eth2
N    10.0.5.8/30           [10] area: 0.0.0.0
                           directly attached to eth3
N    10.0.5.12/30          [20] area: 0.0.0.0
                           via 10.0.5.2, eth1
                           via 10.0.5.6, eth2
N    10.0.5.16/30          [20] area: 0.0.0.0
                           via 10.0.5.2, eth1
N    10.0.5.20/30          [20] area: 0.0.0.0
                           via 10.0.5.6, eth2
N    10.0.5.24/30          [30] area: 0.0.0.0
                           via 10.0.5.2, eth1
N    10.0.5.28/30          [30] area: 0.0.0.0
                           via 10.0.5.2, eth1
N    10.0.5.32/30          [30] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.5.36/30          [30] area: 0.0.0.0
                           via 10.0.5.6, eth2
N    10.0.5.40/30          [20] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.5.44/30          [20] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.5.48/30          [40] area: 0.0.0.0
                           via 10.0.5.2, eth1
                           via 10.0.5.10, eth3
N    10.0.5.52/30          [40] area: 0.0.0.0
                           via 10.0.5.2, eth1
                           via 10.0.5.10, eth3
N    10.0.5.56/30          [30] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.5.60/30          [30] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.5.64/30          [30] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.5.68/30          [40] area: 0.0.0.0
                           via 10.0.5.6, eth2
                           via 10.0.5.10, eth3
N    10.0.5.72/30          [40] area: 0.0.0.0
                           via 10.0.5.6, eth2
                           via 10.0.5.10, eth3
N    10.0.5.76/30          [30] area: 0.0.0.0
                           via 10.0.5.6, eth2
N    10.0.5.80/30          [30] area: 0.0.0.0
                           via 10.0.5.6, eth2
N    10.0.50.1/32          [10] area: 0.0.0.0
                           directly attached to lo
N    10.0.50.2/32          [20] area: 0.0.0.0
                           via 10.0.5.2, eth1
N    10.0.50.3/32          [20] area: 0.0.0.0
                           via 10.0.5.6, eth2
N    10.0.50.4/32          [30] area: 0.0.0.0
                           via 10.0.5.2, eth1
N    10.0.50.5/32          [40] area: 0.0.0.0
                           via 10.0.5.2, eth1
                           via 10.0.5.10, eth3
                           via 10.0.5.6, eth2
N    10.0.50.6/32          [30] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.50.7/32          [20] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.50.8/32          [40] area: 0.0.0.0
                           via 10.0.5.2, eth1
N    10.0.50.9/32          [30] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.50.10/32         [40] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.50.11/32         [40] area: 0.0.0.0
                           via 10.0.5.10, eth3
N    10.0.50.12/32         [40] area: 0.0.0.0
                           via 10.0.5.6, eth2
N    10.0.50.13/32         [40] area: 0.0.0.0
                           via 10.0.5.6, eth2
                           via 10.0.5.10, eth3
N    10.0.50.14/32         [30] area: 0.0.0.0
                           via 10.0.5.6, eth2

============ OSPF router routing table =============

============ OSPF external routing table ===========

WA# sh ip ospf neighbor 

    Neighbor ID Pri State           Dead Time Address         Interface            RXmtL RqstL DBsmL
10.0.50.2         1 Full/DR           32.439s 10.0.5.2        eth1:10.0.5.1            0     0     0
10.0.50.3         1 Full/DR           32.542s 10.0.5.6        eth2:10.0.5.5            0     0     0
10.0.50.7         1 Full/DR           33.041s 10.0.5.10       eth3:10.0.5.9            0     0     0
WA# sh ip ospf interface 
dummy0 is down
  ifindex 7, MTU 1500 bytes, BW 0 Kbit   <BROADCAST,NOARP>
  OSPF not enabled on this interface
eth0 is up
  ifindex 5, MTU 1500 bytes, BW 0 Kbit   <UP,BROADCAST,RUNNING,MULTICAST>
  OSPF not enabled on this interface
eth1 is up
  ifindex 1, MTU 1500 bytes, BW 0 Kbit   <UP,BROADCAST,RUNNING,PROMISC,MULTICAST>
  Internet Address 10.0.5.1/30, Broadcast 10.0.5.3, Area 0.0.0.0
  MTU mismatch detection:enabled
  Router ID 10.0.50.1, Network Type BROADCAST, Cost: 10
  Transmit Delay is 1 sec, State Backup, Priority 1
  Designated Router (ID) 10.0.50.2, Interface Address 10.0.5.2
  Backup Designated Router (ID) 10.0.50.1, Interface Address 10.0.5.1
  Multicast group memberships: OSPFAllRouters OSPFDesignatedRouters
  Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
    Hello due in 5.703s
  Neighbor Count is 1, Adjacent neighbor count is 1
eth2 is up
  ifindex 2, MTU 1500 bytes, BW 0 Kbit   <UP,BROADCAST,RUNNING,PROMISC,MULTICAST>
  Internet Address 10.0.5.5/30, Broadcast 10.0.5.7, Area 0.0.0.0
  MTU mismatch detection:enabled
  Router ID 10.0.50.1, Network Type BROADCAST, Cost: 10
  Transmit Delay is 1 sec, State Backup, Priority 1
  Designated Router (ID) 10.0.50.3, Interface Address 10.0.5.6
  Backup Designated Router (ID) 10.0.50.1, Interface Address 10.0.5.5
  Multicast group memberships: OSPFAllRouters OSPFDesignatedRouters
  Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
    Hello due in 5.807s
  Neighbor Count is 1, Adjacent neighbor count is 1
eth3 is up
  ifindex 3, MTU 1500 bytes, BW 0 Kbit   <UP,BROADCAST,RUNNING,PROMISC,MULTICAST>
  Internet Address 10.0.5.9/30, Broadcast 10.0.5.11, Area 0.0.0.0
  MTU mismatch detection:enabled
  Router ID 10.0.50.1, Network Type BROADCAST, Cost: 10
  Transmit Delay is 1 sec, State Backup, Priority 1
  Designated Router (ID) 10.0.50.7, Interface Address 10.0.5.10
  Backup Designated Router (ID) 10.0.50.1, Interface Address 10.0.5.9
  Multicast group memberships: OSPFAllRouters OSPFDesignatedRouters
  Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
    Hello due in 6.311s
  Neighbor Count is 1, Adjacent neighbor count is 1
ip6tnl0 is down
  ifindex 9, MTU 1460 bytes, BW 0 Kbit   <NOARP>
  OSPF not enabled on this interface
lo is up
  ifindex 6, MTU 16436 bytes, BW 0 Kbit   <UP,LOOPBACK,RUNNING>
  Internet Address 10.0.50.1/32, Area 0.0.0.0
  MTU mismatch detection:enabled
  Router ID 10.0.50.1, Network Type LOOPBACK, Cost: 10
  Transmit Delay is 1 sec, State Loopback, Priority 1
  No designated router on this network
  No backup designated router on this network
  Multicast group memberships: <None>
  Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
    Hello due in inactive
  Neighbor Count is 0, Adjacent neighbor count is 0
sit0 is down
  ifindex 8, MTU 1480 bytes, BW 0 Kbit   <NOARP>
  OSPF not enabled on this interface

Thing to do. If you want to help us to improve this example (please, tell us about :), the following enhancements could be done:

A IPv6 version of the scenario (using the <ipv6> tags)

VNUML Description

<?xml version='1.0' encoding='UTF-8'?>
<!DOCTYPE vnuml SYSTEM '/usr/share/xml/vnuml/vnuml.dtd'>
<vnuml>
<global>
    <version>1.9</version>
    <simulation_name>nsfnet</simulation_name>
    <automac/>
    <vm_mgmt type="private" network="10.250.0.0" mask="16" offset="0">
       <host_mapping/>
    </vm_mgmt>
    <vm_defaults exec_mode='mconsole'>
       <filesystem type='cow'>/usr/share/vnuml/filesystems/root_fs_tutorial</filesystem>
       <kernel>/usr/share/vnuml/kernels/linux</kernel>
       <console id='0'>pts</console>
    </vm_defaults>
    <extension plugin="ospfd" conf="nsf-14_conf.xml" />
  </global>
  <net name='il-ne' mode='uml_switch'/>
  <net name='mi-ut' mode='uml_switch'/>
  <net name='dc-ny' mode='uml_switch'/>
  <net name='il-wa' mode='uml_switch'/>
  <net name='ca2-tx' mode='uml_switch'/>
  <net name='dc-tx' mode='uml_switch'/>
  <net name='co-tx' mode='uml_switch'/>
  <net name='ca1-ut' mode='uml_switch'/>
  <net name='dc-nj' mode='uml_switch'/>
  <net name='ca1-wa' mode='uml_switch'/>
  <net name='ca1-ca2' mode='uml_switch'/>
  <net name='nj-pa' mode='uml_switch'/>
  <net name='mi-ny' mode='uml_switch'/>
  <net name='ca2-wa' mode='uml_switch'/>
  <net name='co-ne' mode='uml_switch'/>
  <net name='ga-tx' mode='uml_switch'/>
  <net name='il-pa' mode='uml_switch'/>
  <net name='ny-pa' mode='uml_switch'/>
  <net name='co-ut' mode='uml_switch'/>
  <net name='ga-pa' mode='uml_switch'/>
  <net name='mi-nj' mode='uml_switch'/>
  <vm name='WA'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.1</ipv4>
    </if>
    <if id='1' net='ca1-wa'>
      <ipv4 mask='255.255.255.252'>10.0.5.1</ipv4>
    </if>
    <if id='2' net='ca2-wa'>
      <ipv4 mask='255.255.255.252'>10.0.5.5</ipv4>
    </if>
    <if id='3' net='il-wa'>
      <ipv4 mask='255.255.255.252'>10.0.5.9</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='CA1'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.2</ipv4>
    </if>
    <if id='1' net='ca1-ca2'>
      <ipv4 mask='255.255.255.252'>10.0.5.13</ipv4>
    </if>
    <if id='2' net='ca1-ut'>
      <ipv4 mask='255.255.255.252'>10.0.5.17</ipv4>
    </if>
    <if id='3' net='ca1-wa'>
      <ipv4 mask='255.255.255.252'>10.0.5.2</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='CA2'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.3</ipv4>
    </if>
    <if id='1' net='ca1-ca2'>
      <ipv4 mask='255.255.255.252'>10.0.5.14</ipv4>
    </if>
    <if id='2' net='ca2-wa'>
      <ipv4 mask='255.255.255.252'>10.0.5.6</ipv4>
    </if>
    <if id='3' net='ca2-tx'>
      <ipv4 mask='255.255.255.252'>10.0.5.21</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='UT'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.4</ipv4>
    </if>
    <if id='1' net='ca1-ut'>
      <ipv4 mask='255.255.255.252'>10.0.5.18</ipv4>
    </if>
    <if id='2' net='mi-ut'>
      <ipv4 mask='255.255.255.252'>10.0.5.25</ipv4>
    </if>
    <if id='3' net='co-ut'>
      <ipv4 mask='255.255.255.252'>10.0.5.29</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='CO'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.5</ipv4>
    </if>
    <if id='1' net='co-ut'>
      <ipv4 mask='255.255.255.252'>10.0.5.30</ipv4>
    </if>
    <if id='2' net='co-ne'>
      <ipv4 mask='255.255.255.252'>10.0.5.33</ipv4>
    </if>
    <if id='3' net='co-tx'>
      <ipv4 mask='255.255.255.252'>10.0.5.37</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='NE'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.6</ipv4>
    </if>
    <if id='1' net='co-ne'>
      <ipv4 mask='255.255.255.252'>10.0.5.34</ipv4>
    </if>
    <if id='2' net='il-ne'>
      <ipv4 mask='255.255.255.252'>10.0.5.41</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='IL'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.7</ipv4>
    </if>
    <if id='1' net='il-ne'>
      <ipv4 mask='255.255.255.252'>10.0.5.42</ipv4>
    </if>
    <if id='2' net='il-wa'>
      <ipv4 mask='255.255.255.252'>10.0.5.10</ipv4>
    </if>
    <if id='3' net='il-pa'>
      <ipv4 mask='255.255.255.252'>10.0.5.45</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='MI'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.8</ipv4>
    </if>
    <if id='1' net='mi-ut'>
      <ipv4 mask='255.255.255.252'>10.0.5.26</ipv4>
    </if>
    <if id='2' net='mi-nj'>
      <ipv4 mask='255.255.255.252'>10.0.5.49</ipv4>
    </if>
    <if id='3' net='mi-ny'>
      <ipv4 mask='255.255.255.252'>10.0.5.53</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='PA'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.9</ipv4>
    </if>
    <if id='1' net='il-pa'>
      <ipv4 mask='255.255.255.252'>10.0.5.46</ipv4>
    </if>
    <if id='2' net='ga-pa'>
      <ipv4 mask='255.255.255.252'>10.0.5.57</ipv4>
    </if>
    <if id='3' net='ny-pa'>
      <ipv4 mask='255.255.255.252'>10.0.5.61</ipv4>
    </if>
    <if id='4' net='nj-pa'>
      <ipv4 mask='255.255.255.252'>10.0.5.65</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='NY'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.10</ipv4>
    </if>
    <if id='1' net='mi-ny'>
      <ipv4 mask='255.255.255.252'>10.0.5.54</ipv4>
    </if>
    <if id='2' net='ny-pa'>
      <ipv4 mask='255.255.255.252'>10.0.5.62</ipv4>
    </if>
    <if id='3' net='dc-ny'>
      <ipv4 mask='255.255.255.252'>10.0.5.69</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='NJ'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.11</ipv4>
    </if>
    <if id='1' net='mi-nj'>
      <ipv4 mask='255.255.255.252'>10.0.5.50</ipv4>
    </if>
    <if id='2' net='nj-pa'>
      <ipv4 mask='255.255.255.252'>10.0.5.66</ipv4>
    </if>
    <if id='3' net='dc-nj'>
      <ipv4 mask='255.255.255.252'>10.0.5.73</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='DC'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.12</ipv4>
    </if>
    <if id='1' net='dc-tx'>
      <ipv4 mask='255.255.255.252'>10.0.5.77</ipv4>
    </if>
    <if id='2' net='dc-ny'>
      <ipv4 mask='255.255.255.252'>10.0.5.70</ipv4>
    </if>
    <if id='3' net='dc-nj'>
      <ipv4 mask='255.255.255.252'>10.0.5.74</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='GA'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.13</ipv4>
    </if>
    <if id='1' net='ga-pa'>
      <ipv4 mask='255.255.255.252'>10.0.5.58</ipv4>
    </if>
    <if id='2' net='ga-tx'>
      <ipv4 mask='255.255.255.252'>10.0.5.81</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
  <vm name='TX'>
    <if id='1' net='lo'>
      <ipv4 mask='255.255.255.255'>10.0.50.14</ipv4>
    </if>
    <if id='1' net='ca2-tx'>
      <ipv4 mask='255.255.255.252'>10.0.5.22</ipv4>
    </if>
    <if id='2' net='co-tx'>
      <ipv4 mask='255.255.255.252'>10.0.5.38</ipv4>
    </if>
    <if id='3' net='dc-tx'>
      <ipv4 mask='255.255.255.252'>10.0.5.78</ipv4>
    </if>
    <if id='4' net='ga-tx'>
      <ipv4 mask='255.255.255.252'>10.0.5.82</ipv4>
    </if>
    <forwarding type="ip"/>
  </vm>
</vnuml>

OSPF plugin configuration file

<?xml version='1.0' encoding='UTF-8'?>
<!DOCTYPE ospf_conf SYSTEM '/usr/share/xml/vnuml/ospfd.dtd'>
<ospf_conf>
   <vm name="WA" type="quagga" subtype="lib-install">
      <zebra hostname="WA" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.1</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.0</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.4</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.8</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="CA1" type="quagga" subtype="lib-install">
      <zebra hostname="CA1" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.2</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.12</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.16</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.0</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="CA2" type="quagga" subtype="lib-install">
      <zebra hostname="CA2" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.3</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.12</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.4</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.20</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="UT" type="quagga" subtype="lib-install">
      <zebra hostname="UT" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.4</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.16</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.24</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.28</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="CO" type="quagga" subtype="lib-install">
      <zebra hostname="CO" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.5</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.28</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.32</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.36</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="NE" type="quagga" subtype="lib-install">
      <zebra hostname="NE" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.6</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.32</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.40</ip>
         <area>0.0.0.0</area>
      </network>		
   </vm>
   <vm name="IL" type="quagga" subtype="lib-install">
      <zebra hostname="IL" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.7</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.40</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.8</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.44</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="MI" type="quagga" subtype="lib-install">
      <zebra hostname="MI" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.8</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.24</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.48</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.52</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="PA" type="quagga" subtype="lib-install">
      <zebra hostname="PA" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.9</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.44</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.56</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.60</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.64</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="NY" type="quagga" subtype="lib-install">
      <zebra hostname="NY" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.10</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.52</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.60</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.68</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>		
   <vm name="NJ" type="quagga" subtype="lib-install">
      <zebra hostname="NJ" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.11</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.48</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.64</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.72</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="DC" type="quagga" subtype="lib-install">
      <zebra hostname="DC" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.12</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.76</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.68</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.72</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="GA" type="quagga" subtype="lib-install">
      <zebra hostname="GA" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.13</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.56</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.80</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
   <vm name="TX" type="quagga" subtype="lib-install">
      <zebra hostname="TX" password="xxxx"></zebra>
      <network>
         <ip mask="32">10.0.50.14</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.20</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.36</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.76</ip>
         <area>0.0.0.0</area>
      </network>
      <network>
         <ip mask="30">10.0.5.80</ip>
         <area>0.0.0.0</area>
      </network>
   </vm>
</ospf_conf>

Download

VNUML specification file: Nsf-14.xml
VNUML configuration file: Nsf-14_conf.xml

Old Releases

1.8

Difference between revisions of "Example-NSF-14 1.9"

Latest revision as of 10:59, 10 February 2009

Contents

Scenario

VNUML Description

OSPF plugin configuration file

Download

Old Releases

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

VNUML Documentation

EDIV Documentation

Other Documentation

Tools